1. Compared with the plastic deformation property of the polycrystal copper wire, the SCCW is better;
同种技术生产的单晶和多晶两种线材相比，单晶铜线材的塑性更为优异。
来自互联网
2. Presents numerical simulation of multi point forming of sheet using a finite element polycrystal model.
采用有限元多晶体模型对板材多点成形过程进行了数值模拟研究。
来自互联网
3. The constitutive models of monocrystal and polycrystal MT materials are presented in this dissertation.
本文的研究内容给出了单晶和多晶马氏体相变材料的本构响应模型。
来自互联网
4. The nanometer tetragonal polycrystal zirconia powder was prepared by the super alkaline method at low temperature.
利用低温超强碱法制备出了纳米四方多晶氧化锆粉体。
来自互联网
5. Numerical calculation shows that the constitutive model given here can well simulate the behavior of polycrystal MT.
数值计算结果表明该本构模型能较好模拟多晶材料的马氏体相变本构曲线形态。
来自互联网
6. Kim said, "We will be able to use a low-temperature polycrystal silicon with the sixth-generation size glass substrate."
Kim称：“我们现在已经可以在6G尺寸级别的基板上应用低温多晶硅技术。
来自互联网
7. The Nanbo Company which is located in Yichang is the maximal high-purity polycrystal silicon producing enterprise of China.
位于宜昌市境内南玻公司是全国最大的高纯多晶硅材料生产企业。
来自互联网
8. From the viewpoint of multi-grain structure of material, a polycrystal model is founded based on the crystal plasticity theory.
从材料的多晶体结构角度，基于晶体塑性变形理论建立了多晶体模型。
来自互联网
9. We consider that damage layers on near perfect crystal consist of polycrystal layer, Mosaic structure layer and distorted layer.
我们认为，近完整晶体的切割损伤层是由多晶层、嵌镶结构层和畸变层组成。
来自互联网
10. This article introduces production situation, market demands and prospect of development to polycrystal-line - silicon and its derivative.
本文主要介绍了多晶硅及其衍生物的生产现状，市场需求及发展前景。
来自互联网
11. There are two kinds of cordierites: one occurs as crystalloblastic or irregular polycrystal, which result from unmolten residues of mudstone;
该类花岗岩中存在两种堇青石：一种呈变晶状或不规则状聚晶出现，属于源岩的不熔残余物成因；
来自互联网
12. Numerical simulation of multi point bending process of strip under different loading paths is dealt with the finite element polycrystal model.
采用有限元多晶体模型对无模多点成形条件下不同加载方式的板条多点弯曲成形过程进行了数值模拟。
来自互联网
13. However, there is not any report on the relationship between grain edge length and its neighboring ensemble grains edge length average in the polycrystal.
三维个体晶粒棱长是描述晶粒尺寸的重要参量，多晶体中晶粒及其邻接晶粒的棱长之间的关系至今仍是空白。
来自互联网
14. Crystal plasticity finite element modeling (CPFEM) is realized on the basis of crystal plasticity theory of rate dependent polycrystal constitutive relations.
基于率相关晶体塑性本构模型，实现了晶体塑性学有限元模拟过程。
来自互联网
15. The TEM analysis shows that the matrix of composite coating is polycrystal nickel with the finer grain size, and the organization structure is homogeneous and compact.
TEM分析表明：复合镀层的基体为多晶镍，并且复合镀层晶粒细小，组织结构均匀、致密。
来自互联网
16. Crystal plasticity theory stemming from 1920s includes single crystal constitutive theory and polycrystal constitutive theory, which disclosures laws of material deforming.
17. The microstructure and phases present in hydroxyapatite(HA) reinforced by tetragonal zirconia polycrystal (TZP) were investigated by using transmission electron microscopy(TEM).
18. According to the results, during of the axisymmetry deformation, longitudinal anisotropy and transversal isotropy of polycrystal were obvious with the effective strain increasing.
结果表明，在轴对称变形过程中，随着等效应变的增加，多晶织构显现出明显的横观各向同性及纵向各向异性。
来自互联网
19. This paper discusses a few quality problems encountered in the manufacturing of polycrystal diamond composites(PDC), the reasons that causes the problem and the ways to solve them.
本文报道了在研制多晶金刚石复合材料（PDC）时碰到的一些质量问题及其造成的原因和解决办法。
来自互联网
20. Every series breed specification, high efficiency solar energy producing single crystal silicon, polycrystal silicon and amorphous silicon vanquish the large-scale module and chip only.
生产单晶硅、多晶硅和非晶硅各系列品种规格、高效率的太阳能光伏大型组件及微型组件。
来自互联网
21. This technique is no longer restricted by the formal regularity of diamond polycrystal blank, and can give an effective tight protection to diamond polycrystal blank in wire-drawing die.
该工艺不受人造聚晶金刚石外形及尺寸的限制，可对拉丝模中的人造金刚石聚晶块提供有效的紧固保护。
来自互联网
22. Thus, the single-crystal manufacturing apparatus can shorten the melting time period of the polycrystal thereby to shorten the cycle time and to reduce the production cost and the power cost.
23. Using conventional method of making visible light emitting porous silicon, an emitting sample with even visible light, detected by naked eyes. is prepared on unpolished polycrystal silicon wafer.
24. Using conventional method of making visible light emitting porous silicon, an emitting sample with even visible light, detected by naked eyes. is prepared on unpolished polycrystal silicon wafer.
